2011年からの看板とLEDストリップ照明工場

LED PCB ボードの設計と組み立て: カスタム WS2815 ケーススタディ

An equipment manufacturer approached SignliteLED to develop a compact LED PCB board that could become a standardized lighting component across its product line.

Each finished product required six short LED boards arranged as two independent channels. Three boards in each channel needed to connect in sequence without soldering. The system also required individually addressable RGB control, a backup data path, detachable cables and mechanical mounting without adhesive.

The initial request specified WS2815 LEDs and preferred direct operation from the equipment’s existing 24V DC supply. Our technical review confirmed that the selected WS2815 solution required 12V. The customer retained the existing 24V architecture and added a dedicated 24V-to-12V power supply for the LED boards.

The approved custom LED PCB used 11 WS2815 LEDs, dual four-pin connectors, an aluminum substrate and two types of custom cable. The project progressed from the initial inquiry to documented finished-goods testing in approximately four weeks. After drawing approval, manufacturing, assembly and pre-shipment testing, the completed products were shipped to the customer.

YouTube ビデオ

The video demonstrates the completed WS2815 LED PCB system, including multi-board operation, dynamic color control and the vehicle warning-light application. The customer-specific PCB dimensions, connectors and cable arrangement are detailed in the case study below.

プロジェクトの概要

プロジェクトアイテムFinal solution
製品タイプCustom addressable LED PCB board
LEDWS2815 addressable RGB LED
動作電圧DC12V
Existing equipment supply24V DC with a dedicated 24V-to-12V converter
LEDs per PCB11
LED pitch7.95mm center to center
Overall PCB size112.0 × 15.0mm
LED layout span86.6mm as marked on the PCB drawing
Customer’s diffuser openingIncreased from 70mm to 85mm
PCB substrateアルミニウム
PCB appearanceWhite solder mask with black silkscreen
ConnectionsInput and output connectors at opposite ends
信号V+, GND, main data and backup data
Board-to-board cable300mm with connectors at both ends
Controller input cable1000mm with bare wires at one end and a PCB connector at the other
Mounting conceptScrews or clips rather than adhesive
Project statusManufactured, tested and shipped

Recorded Project Timeline

マイルストーン日付
Initial inquiry7-Oct-26
Final drawing approval21-Oct-26
Finished-goods test documented5-Nov-26
Delivery statusShipped after the pre-shipment check

The dates describe this project’s recorded development and manufacturing process. They do not represent a standard lead time for every custom LED PCB order. Tooling, component availability, quantity and testing requirements affect each schedule.

The Customer’s Custom LED PCB Requirements

The original concept called for six LED PCB sections in each finished product. Two control channels would each operate a daisy chain of three boards.

The first request specified seven WS2815 LEDs on each PCB with approximately 10mm spacing. Every board needed one input connector and one output connector so installers could join the boards without soldering.

The project also required two cable assemblies:

  • A 1000mm input cable with bare wires for the customer’s control system and a connector for the first LED PCB board
  • A 300mm linking cable with connectors at both ends for joining adjacent boards

The customer’s initial wiring diagram defined the board arrangement and cable lengths before the final electrical and mechanical design had been completed.

Initial-Customer-Wiring-Concept

Initial customer wiring concept. The original plan used two channels with three LED PCB boards per channel, 1000mm input cables and 300mm linking cables. The voltage, LED quantity and backup-data routing were revised during engineering review.

This diagram documented the required system topology rather than the final production specification. It still showed seven LEDs per board, direct connection to the equipment’s 24V supply and three conductors for V+, GND and DATA. The final design later changed to 11 LEDs, a dedicated 12V supply and a four-conductor path that also carried the WS2815 backup-data signal.

The customer preferred WS2815 LEDs because the application required individually addressable RGB control and a backup data line. The customer also planned to secure the boards with screws or custom clips instead of adhesive tape.

A separate mechanical concept showed an initial 14mm PCB width, a 6mm proposed LED pitch, a 70mm diffuser opening and connectors at both ends. These dimensions served as the starting point for engineering review rather than approved production values.

initial-custom-LED-PCB-concept-with-11-LEDs-and-dual-connectors

Initial mechanical concept. The proposed 14mm PCB width, 6mm LED pitch and 70mm diffuser opening were revised after the connector footprint, LED package and available installation space were reviewed.

A standard flexible LED strip or conventional sign module could not meet the required LED spacing, mechanical mounting method and connector arrangement. This application therefore required a purpose-built PCB with addressable LEDs, dual connectors and dedicated cable assemblies. Learn more about SignliteLED’s custom LED PCB design and manufacturing capabilities.

Before PCB layout began, the team needed to resolve three differences between the initial concept and a production-ready design:

  • The equipment supplied 24V, while the selected WS2815 solution operated at 12V.
  • The initial wiring diagram did not show the WS2815 backup-data conductor.
  • The proposed LED pitch and PCB width did not provide enough space for the final LED and connector layout.

These points were addressed during the electrical and mechanical review described in the following sections.

Resolving the 24V and 12V System Difference

The equipment already contained a 24V DC supply, so the initial inquiry asked whether the WS2815 LED PCB could operate directly from 24V.

The selected WS2815 configuration operates at 12V. Connecting the equipment’s 24V supply directly to the LED boards would create an electrical mismatch. The customer instead confirmed a dedicated 24V-to-12V, 3A power supply for the lighting system.

The final power and control architecture separated the equipment supply from the LED operating voltage:

  • The equipment retained its existing 24V DC architecture.
  • A dedicated converter supplied 12V to the LED PCB boards.
  • The customer’s control hardware supplied the addressable data signal.
  • Every PCB connector carried V+, GND, main data and backup data.

This review resolved the voltage difference before PCB design and production. In a custom LED circuit board project, the equipment supply, LED operating voltage and controller interface need separate confirmation. Treating them as one specification can introduce an avoidable compatibility problem.

Developing the Production-Ready LED PCB Board

Once both parties confirmed the electrical architecture, the project moved into detailed PCB and mechanical development. Several specifications changed between the original inquiry and the approved production drawing.Increasing the Design to 11 WS2815 LEDs

Increasing the Design to 11 WS2815 LEDs

After reviewing the illuminated area and required resolution, the customer increased the LED quantity from the original minimum of seven to 11 LEDs per PCB.

The engineering layout established a 7.95mm center-to-center LED pitch. A proposed 6mm pitch left insufficient space for the selected LED packages and surrounding circuit requirements.

The approved drawing specified three separate dimensions:

  • 7.95mm LED center-to-center pitch
  • 112.0mm overall PCB length
  • 86.6mm LED layout span
custom-WS2815-LED-PCB-drawing

The 86.6mm value is an independently marked PCB drawing dimension. It is not the result of multiplying the LED quantity by the 7.95mm pitch.

After reviewing the drawing, the customer enlarged the equipment’s diffuser opening from 70mm to 85mm. The 85mm opening and the 86.6mm PCB layout span describe different parts of the assembly. When centered, the opening overlaps the layout span by approximately 0.8mm at each end. The customer reviewed and accepted this fit before production.

LED quantity, PCB length, optical resolution and diffuser dimensions formed one mechanical system. Changing one value affected the surrounding product design.

Expanding the PCB Width to 15mm

The original concept allowed a 14mm board width. During layout development, that width left insufficient space for the selected connectors, routing and surrounding board material.

The engineering team increased the PCB width to 15mm, and the customer confirmed that the mounting structure could accommodate the change.

A one-millimeter increase appears small, but it creates useful space on a narrow LED PCB board. Connector clearance, copper area, routing and board-edge strength all depend on the available width.

Confirming the connector footprint before production prevented an impractical terminal layout and reduced the risk of mechanical interference during installation.

Using Dual Connectors for Solderless Daisy-Chaining

Each PCB received a connector at both ends. One connector serves as the input and the other as the output. Detachable 300mm cables connect three boards into one channel.

Both connectors carry the same four electrical paths:

  1. V+
  2. GND
  3. Main data
  4. Backup data

The 1000mm input cable connects the customer’s control hardware to the first PCB. It uses bare wires at the controller end and the specified four-pin connector at the board end.

This arrangement provides several practical advantages:

  • Installers can connect the LED boards without soldering inside the equipment.
  • A single PCB or cable can be removed without cutting the remaining harness.
  • Standardized cable lengths simplify repeat production.
  • Consistent input and output connections reduce wiring variation.
  • The main and backup data paths continue through the complete chain.

The PCB silkscreen and assembly documentation still need to identify input direction, output direction and pin assignment clearly. A detachable connector reduces installation work only when its orientation and wiring are unambiguous.

Similar connector positions, cable assemblies and board dimensions are available through our custom linear LED module service.

Selecting an Aluminum PCB Substrate

Thermal management entered the discussion before production. Eleven addressable RGB LEDs were concentrated on a short and narrow board, and the customer asked whether the design needed additional heat dissipation.

The customer and engineering team selected an aluminum substrate for the final カスタム LED PCB. The aluminum base spreads heat more effectively than a conventional low-power PCB structure and provides a mechanically stable foundation for screw or clip mounting.

The material choice was specific to this project. Not every WS2815 application requires an aluminum PCB. Here, LED density, compact dimensions, mounting conditions and long-term reliability supported the decision.

The visible surface used white solder mask with black silkscreen. The white surface suited the optical environment behind the diffuser, while the black markings kept connector and orientation information readable.

Routing Power and Maintaining the Backup Data Path

The customer specified that the V+ and GND paths needed enough copper capacity for a 1A design requirement. The PCB layout therefore used appropriate trace widths and copper areas for power distribution.

The completed board contained 11 WS2815 LEDs. At approximately 0.66A under an estimated full-white condition, the 1A routing target provided additional current capacity. The dedicated 3A converter also supplied headroom for the planned system arrangement.

Local decoupling capacitors were positioned close to the LEDs to stabilize the supply during changes in RGB output.

The data layout carried both the primary and backup signals from the input connector, through the LED sequence and onward to the output connector.

A backup-data LED does not create system-level redundancy by itself. The PCB traces, connectors and cables must all preserve the additional signal. In this project, all four conductors continued through the complete connection chain.

Drawing Review and Customer Approval

Production began only after the customer reviewed the main electrical and mechanical details.

Drawing itemApproved value
LED type and quantity11 × WS2815
LED pitch7.95mm center to center
Overall PCB size112.0 × 15.0mm
LED layout span86.6mm as marked on the PCB drawing
Customer’s diffuser openingIncreased from 70mm to 85mm
PCB素材Aluminum substrate
Surface appearanceWhite solder mask with black silkscreen
Connector arrangementFour-pin input and output connectors
Signal pathsV+, GND, main data and backup data
Cable assemblies1000mm input cable and 300 mm board-to-board cable

The customer accepted the 15mm board width and the fit between the 85mm diffuser opening and the 86.6mm PCB layout span. This approval established a clear production baseline for the PCB, mounting structure and surrounding optical components.

The drawing review also prevented the factory from making assumptions about the available installation space. Both parties confirmed the mechanical changes before manufacturing started.

LED PCB Assembly and Custom Cable Production

After drawing approval, the project entered PCB manufacturing, component assembly and cable production.

The LED PCB assembly process covered the aluminum boards, WS2815 LEDs, local capacitors and four-pin connectors. Production inspection also checked the white solder mask, black silkscreen, connector placement and input/output orientation.

The cables formed part of the finished assembly rather than an accessory selected after PCB production.

1000mm Controller Input Cable

The longer cable connected the customer’s control hardware to the first PCB in each channel.

One end remained as bare wires for integration with the customer’s control system. The opposite end used the selected four-pin PCB connector.

This cable carried 12V power, ground, main data and backup data to the first board.

300mm Board-to-Board Cable

The shorter cable used matching connectors at both ends. It joined the output of one PCB to the input of the next PCB, creating a detachable three-board channel.

Producing the boards and cables as one project kept the connector family, pin count and wiring sequence consistent. It also reduced the wiring work required during equipment assembly.

Pre-Shipment Testing of the LED PCB Assembly

Before packing, multiple completed boards were connected through the custom cable assemblies and powered together.

The documented test confirmed that:

  • The connected PCB boards powered on.
  • The LEDs illuminated.
  • The board-to-board cables completed the required connections.
  • Multiple PCB assemblies operated together in the planned chain.
  • The connectors and visible cable assemblies followed the intended arrangement.

The test provided evidence of basic power, illumination and interconnected operation before shipment.

Its scope needs to be described accurately. The available record does not document a deliberate LED-failure test of the backup data path, a long-duration thermal qualification or operation inside the customer’s final equipment.

Those checks require separate test procedures, defined operating conditions and acceptance criteria. The phrase “tested before shipment” in this case refers to the recorded connection and lighting test, not a complete reliability certification.

custom-WS2815-LED-PCB-board

Production Completed and Shipped to the Customer

After assembly and pre-shipment testing, the finished LED PCB boards and both cable types were organized into complete sets.

The shipment included:

  • Finished 12V WS2815 aluminum LED PCB boards
  • 1000mm controller input cables
  • 300mm board-to-board connecting cables

The products were packed and shipped to the customer. This completed the supplier-side process from inquiry and technical review through drawing approval, LED PCB assembly, cable production and pre-shipment testing.

Installation and long-term performance inside the customer’s finished equipment remain separate from the factory checks documented in this case study.

custom-ws2815-led-pcb-batch-production

What This Custom LED PCB Project Demonstrates

Decision pointProject responseProduction result
24V equipment supply versus 12V WS2815 operationAdded a dedicated 24V-to-12V, 3A power supplyRetained the equipment’s 24V architecture while supplying the LED boards correctly
LED quantity and illuminated areaIncreased each PCB to 11 LEDs at 7.95mm pitchCustomer accepted the relationship between the PCB layout and revised diffuser opening
Connector size and PCB widthIncreased the PCB width to 15mm and fitted connectors at both endsCreated a detachable, solderless three-board chain
Backup data routingCarried V+, GND, main data and backup data through both connectors and cable typesPreserved all four electrical paths throughout the chain
熱管理Changed the design to an aluminum substrateImproved heat spreading and mechanical stability
Equipment installationSupplied 1000mm input cables and 300mm linking cablesReduced wiring work during equipment assembly
Pre-shipment verificationConnected and powered multiple finished boardsConfirmed basic illumination and interconnected operation before shipment

The project converted an initial lighting concept into a production-ready LED PCB assembly. Electrical compatibility, mechanical dimensions, thermal management, connectors, cables and testing were resolved as parts of one system before delivery.

よくあるご質問

To evaluate a similar LED PCB board design and assembly project, provide as much of the following information as possible:

  • – Available equipment supply voltage
  • – Required LED operating voltage
  • – LED type or control protocol
  • – LED color and addressability requirements
  • – Number of LEDs per PCB
  • – Preferred LED pitch
  • – Maximum PCB length and width
  • – PCB material preference
  • – Main and backup data requirements
  • – Connector model and pin assignment
  • – Input and output direction
  • – Cable types and lengths
  • – Mounting-hole, screw or clip requirements
  • – Diffuser distance and illuminated area
  • – Prototype and production quantities
  • – Required functional, thermal or failure tests

A wiring plan, mechanical drawing or installation-space model helps define the project efficiently. When some specifications remain open, begin with the fixed electrical, mechanical and optical limits, then develop the remaining parameters around them.

Planning a custom LED PCB project? Send the information above, together with any available drawings, wiring plans or reference samples, through Contact SignliteLED. Our team can review the electrical, mechanical, thermal and production requirements before quotation.

カスタム 12V-DMX-LED-モジュール-ケーススタディカスタム 12V-DMX-LED-モジュール-ケーススタディ
カスタム LED モジュールのケース スタディ: 問い合わせから出荷までの 12V DMX プロジェクト
ほとんどの LED モジュールの問い合わせは同じパスをたどります。購入者が仕様を送信し、メーカーの見積もりを送信し、数字が機能する場合は生産が開始されます。 しかし、要件が標準カタログ (非標準電圧、特定のピクセル グループ化、または特定の制御プロトコル) から外れると、プロジェクトの成功はしばしば依存します。
音響 LED 照明費用音響 LED 照明費用
音響照明のコストに影響するものは何ですか?
音響照明の価格が予想よりも異なる理由 商業用インテリアの音響照明を評価するとき、多くのバイヤーは、似たような外観の製品の価格が大きく異なる可能性があることに気づきました。 アコースティック ペンダント ライトまたはアコースティック シーリング ライトは、比較できるように見える場合がありますが、各製品のコストは非常に異なることがよくあります。 よくある...
PCB LED 設計PCB LED 設計
高 CRI LED モジュールの PCB 設計のベスト プラクティス
高 CRI LED モジュールは、人工照明の下で正確に色を再現するように設計された照明システムです。 CRI、またはカラー レンダリング インデックスは、自然な参照と比較して、光源がどれだけ色を表示するかを測定します。 CRI 値の高い LED は、建築照明、小売店、医療環境、スタジオ、および...
LED PCB アセンブリLED PCB アセンブリ
スマート接続照明用の LED PCB アセンブリ
スマート接続照明用の LED PCB アセンブリは、LED を統合し、制御電子機器、およびワイヤレス接続を単一の信頼性の高い PCB プラットフォームに統合するプロセスです。 標準の LED ボードとは異なり、これらのアセンブリーは、高出力の照明コンポーネントとマイクロコントローラ、センサー、および RF モジュールを組み合わせています。 これにより、熱制御、信号の整合性、および...
カスタム PCB LED の最も正確な見積もりを取得するにはどうすればよいですかカスタム PCB LED の最も正確な見積もりを取得するにはどうすればよいですか
カスタム PCB LED の最も正確な見積もりを取得するにはどうすればよいですか?
LED 照明業界、特に LED ストリップ ライト、LED モジュール、COB LED ボード、およびカスタマイズされた照明ソリューションの場合、PCB は単なるサポート コンポーネントではありません。これは、製品のパフォーマンス、信頼性、寿命、およびコスト効率を決定する重要な要素です。 ただし、多くの購入者は、LED PCB を調達するときに同じ問題に遭遇します。なぜ...
PCB LEDPCB LED
スマート街路照明アプリケーション向け PCB LED
スマート街路照明の PCB LED は、発光ダイオードを目的のプリント回路基板に直接取り付けて、電気動作の安定化、放熱、長時間の安定した光出力を保証する屋外照明ソリューションです。 これらのソリューションは、スマート街路照明システムに広く適用されています...

共有:

フェイスブック
ツイッター
ピンタレスト
リンクトイン
購読する
通知する
ゲスト
0 コメント
最古
最新 最も投票された
インラインフィードバック
すべてのコメントを表示

SignliteLEDブログを検索

カテゴリー

上部へスクロール

今すぐ見積もりを取る