Signage & LED Strip Lighting Factory Since 2011

What should be paid attention to when installing LED injection molding modules?

What should be paid attention to when installing LED injection molding modules

Nowadays, there are many brands in the LED lamp market, and there are countless types. LED injection molding modules account for a large proportion of the entire LED lamp market, and the scope of use is also wider. LED injection molding modules are widely used in hotels, bars, stages, etc. The traffic is relatively large Therefore, the safety of LED injection molding modules must be emphasized. Safety and standard installation can avoid many hidden dangers. Today, let’s talk about what should be paid attention to when installing LED injection molding modules.

1. Special switching power supply (not waterproof) for LED injection molding module should pay attention to waterproof measures.

2. The switching power supply should adjust the output voltage according to the characteristics of the injection molding module, and the voltage adjustment button should not be rotated arbitrarily during use!

3. LED injection modules are all low voltage products. 220V AC is not applicable, so a dedicated power supply must be used.

4. There are positive and negative poles in the LED injection molding module. Pay attention to the corresponding positive and negative poles during installation. If the positive and negative poles are reversed, the module will not emit light, but it will not damage the LED module. Just change the connection. Can not adjust the large and small voltage!

5. During the installation of the LED injection molding module, it is required to use double-sided adhesive or woodworking glue to make the module slot and the plastic bottom plate firmly adhered. When using double-sided tape, you must apply glass glue, otherwise the module will fall off under the outdoor sunlight for a long time, this is very important!

6. When the LED injection module is installed in the blister letter or box, try to form as many circuits as possible, and the number of modules in series should be as small as possible, not more than 15~20 groups (please read the relevant instructions), otherwise it will be under pressure The impact of the drop, and it is very likely to cause excessive single-channel current to burn the circuit board!

7. For LED injection modules that have not been waterproofed, rainwater should be prevented from entering when they are installed on plastic letters or boxes.

8. The spacing of LED injection modules can be adjusted according to the actual situation such as brightness and module size, and the quantity per square is generally between 50-100 groups. When arranging LED modules, attention should be paid to the uniformity of light emission and brightness requirements; the distance between LED injection molding modules and the font side is generally 2-5 cm, and the vertical and horizontal distance between modules is recommended to be 2-6 cm . When installing the LED injection molding module, do not push and squeeze the components on the module to avoid damage to the components. The connecting wires inside should be fixed on the bottom plate with glass glue to avoid shading.

9. The distance between the LED injection molding module and the surface of the illuminant should be well controlled, so as to ensure the uniformity and brightness of the light, so the thickness of the light box is also very important.

best LED strips for color uniformity (1)best LED strips for color uniformity (1)
Philips LED Strips – 2025 Buyer's Guide for High power LED strip light
When selecting the right LED strips for your commercial or architectural lighting project, it’s important to weigh all available options. Among the top choices in the market, Philips stands out with its MASTER and CorePro series. In this comprehensive comparison, we’ll explore the differences between these two series and show...
DMX LED neon strip_Facade Lighting SolutionsDMX LED neon strip_Facade Lighting Solutions
How Does DMX512 Control Pixel LED Neon Strips?
DMX512 control systems are widely used in modern architectural contour and façade lighting projects to achieve precise and dynamic lighting effects. In contrast to RGB strips, which can only change color as a whole, pixel LED neon strips are addressable on a point-by-point basis. You can control each pixel independently...
Applications for KNX SystemsApplications for KNX Systems
KNX Control Equipment Introduction
Related blogs following: Can DMX512 be used in KNX control systems?Guide to KNX Smart Control Systems What Is A KNX System? The KNX system (Konnex) is a standard based on an earlier 485 topology optimized to be homologous to 485. They are identical in that they have two communication lines and differ in...
Digital-LED-Neon-FlexDigital-LED-Neon-Flex
What are the Types of Neon Strips
What is LED Neon Flex Lights? LED Neon Flex is a versatile, silicone-based strip that features embedded LEDs, crafted to replicate the appearance of traditional glass neon lights. This innovative product is suitable for both indoor and outdoor use, allowing for a wide range of visual effects, including static illumination, single-color...
LED-neon-flex-is-made-of-what-materialLED-neon-flex-is-made-of-what-material
LED neon flex is made of what material?
In recent years, LED neon flex has grown in popularity as an energy- and environmentally-conscious lighting solution. LED neon flex is made composed of tiny, flexible LED lights covered in a silicone or PVC jacket, in contrast to conventional glass neon lights. These LED lights are a safe and low-maintenance...
Can-LED-Neon-Flex-be-cutCan-LED-Neon-Flex-be-cut
Can LED Neon Flex be cut?
Due to its adaptability, energy economy, and simplicity of installation, LED Neon Flex is a flexible lighting option that has grown in popularity. Due to its flexibility, it can be moulded and molded into any pattern and is frequently used to create eye-catching displays and signage. Is it possible to...

Share:

Facebook
Twitter
Pinterest
LinkedIn

发表评论

Your email address will not be published. Required fields are marked *

Search SignliteLED Blog

Categories

To top

Get a Quote Now